• Welcome to the Pontiac Trans Am Community, the Official Home of the PTA! Sign up for a (FREE) account today!

My 1978 Z28 Camaro (I Know Not A Firebird)

70formula

Well-known member
Joined
Feb 7, 2023
Messages
165
Reaction score
231
Points
43
Location
Springfield, Oregon
Didn't get any photos but crossed some of the major things off the to do list. The brake system is now together, and all new. Today I got the drum setups all replaced w/ new wheel cylinders. Ran the new stainless axle brake lines to cylinders, and new flex to steel lines all done, making the system finally sealed and complete.

This was my first time doing drum brakes, I was going to do the firebirds but my father in law was bored and ended up doing it while I was in class. I've been wanting to see how they all work, and glad I got to learn em. The first side I fought for a bit because I broke the cardinal rule...I didn't take any photos of the before to compare to, and I didn't notice a few key arrangements in my gung hoe let's get them apart and replaced. So one side fought me a bit due to my inexperience and not thinking. But the second side was a breeze and went together very nicely in no time. I realized when I had everything apart that I should have bought parking cable setup as well. Oh well, that will be a project for a later date.

Master cylinder was bleed, and then the hard lines connected to it. Then ran out of daylight, so tomorrow I will bleed the full system, get the rear u joint in....then I should be able to....do a burnout!
 
  • Like
Reactions: Knightrider189

70formula

Well-known member
Joined
Feb 7, 2023
Messages
165
Reaction score
231
Points
43
Location
Springfield, Oregon
Well, today was a rough day working on the Camaro, where everything wanted to fight me until I just said ok, its time to call it a day and have a stiff drink.

I used a vacuum pump to get the bulk of the air out of the lines, and then my father in law and I tried to bleed the final amount. But for whatever reason, we could not seem to get the master cylinder to actually pump up and pressurize at all with the car off. So, we figured, ok let's try hooking the power brake booster up to the motor running. Started the car but in a mili second realized the 4 speed shifter still isnt right, as though it was in neutral, the driveshaft was spinning so shut the car off. Pulled the driveline off, went to restart the car...will not fire. Cranked and cranked like I lost ignition. So checked for power at the switch and then at the power wire to the distributor, both had power. No miles on it yet but seems like the brand new distributor took a crap on me. So figured ok that sucks, but I still have a new u joint to install, lets get the driveline fixed atleast. took the old u joint off, went to put new one on, opened the new one and the cap had come off and the needles were everywhere. Got them all cleaned up, back in the cup nicely, went to put together, and while pressing the zerg fitting was destroyed. And that's when I knew today's progress was not happening.

Stupid cars. Why couldn't I just love stock Honda civics lol.
 

70formula

Well-known member
Joined
Feb 7, 2023
Messages
165
Reaction score
231
Points
43
Location
Springfield, Oregon
My father-in-law fought the brakes for a while trying to figure out what was going wrong...turns out we have a part combability issue. I bought the power brake / mc setup as a kit from second gen graveyard, but that didnt mean that they will actually work together apparently. We kept not being able to really get any pressure built up. First it seemed like a brake hose was to fault as it started leaking but turns out the line had only one copper washer. Put one on top and bottom and resolved that. So, then we tried again, but realized it was something with the master. Took it apart to see if the rod was actually moving and saw that it was adjustable. So tried at half out, then at barely in the threads at max and still had 0 engagement of the master. So realized we need a long rod.
 
Last edited:
  • Like
Reactions: Knightrider189

70formula

Well-known member
Joined
Feb 7, 2023
Messages
165
Reaction score
231
Points
43
Location
Springfield, Oregon
Second gen graveyard got me a new rod on the way, apparently, they sell both styles of master's and is supposed to match the rod to the master depth type. just an oversight but took me way longer than it should have to figure it out.

Today I got both the gas pedal and throttle cable set up and got the clutch pedal and clutch rod adjustments done. I also got the drive lines new u joint installed and got it installed. I tinkered a bit on the shift linkages and tightened up the shifter as well and am much happier with finding neutral.